Alfa Headlight Lenses

Using the same technology we ulilitized in developing the Rolls-Royce glass Lenses.

They are made from German watchmaker's glass, beveled and then the pattern is printed. They fit the Pocher provided reflectors.

Part No.A047 $30.00 per pair

The Alfa Safety Wire Kit

For the advanced builder! The Studs are cast in bronze and then nickel plated...comes with the hole for the wire and the 28 gauge wire. Also, we provide in the Kit a #61 drill. Pocher shows the spot for 36 Studs. However, the number can vary. Our Kit includes 4 trees with 12 Studs each.

For several examples of prototype use, click here

Complete Kit, includes 48 Studs, 2 yds. of 28 gauge wire and #61 drill - Part No.A046 $40.00

Single Tree of 12 Studs - Part No. 046a $12.00

Wing-nuts

Now, thanks to the efforts of "Wally" Van Orden, we can offer the Wing-nuts to complete the assembly of the Rear Brake Levers. Cast in bronze and threaded for the 2 mm Pocher rods.

Part No. A034a $8.00 per pair

Perfect Alfa Script

We have had many requests over the years for a prototypically correct Alfa Script. We just received these from our photo-etcher...in .20 stainless steel. Perfect!

Part No.A036 $6.00 each

A new fun part for your Alfa!

Crank Cap

One would never leave the Hand Crank in the shaft...so, they would insert this nifty Cap to protect the internal threads. We always scratch built them for our models. Now every Alfa model can have one. They are cast in bronze and nickel plated...and, cheap!

Part No.A044 $5.00 each

The Alfa Knock-Off Hubs

After many months of trial and error (many errors!), the Alfa Knock-Off Hubs are finished. Because they will be bolted on and off many times, we felt casting them with the threaded bolt in bronze would not be satisfactory. Our good friend, Bob Breslauer, came up with the solution. The stainless steel threaded bolt is cast in the mold. We didn't even know it could be done! He, also, engraved the beautiful raised Alfa script.

We have often been asked what we use for the prototype in designing our products. For the Alfa Knock-Off Hubs there was a wide choice...we chose this design for it's elegance and difference from the Pocher.

The Hubs are nickel plated. The results speak for themselves! The easiest retrofitting part we have ever produced...and, one of the best improvements from the Pocher part they replace.

Part No. A041 $100.00 set of four.

The Alfa Shock Absorber Assembly

We are proud to offer the Alfa Shock Absorber Assembly which includes the Chassis Supports, End Plates, Adjuster and End Mounts. We once again thank our friend "Wally" Van Orden for allowing us to cast his masters. The End Mounts require modifications to the Pocher shock. Also, we include the extra shock arm required for the front shocks. We provide instructions with photos.

Click here for Instructions

Alfa Shock Absorber Assembly (Spider, Coupe - one set of rear shocks) Part No.A042 $120.00 complete set

Alfa Shock Absorber Assembly (Monza) - two sets of rear shocks) Part No.A043 $170.00 complete set

The Alfa Steering and Front Brake Assembly

Everything in the above photo (except the Pocher back plate and tie rod) is made by MML.

Under development for almost a year, the Alfa Steering and Front Brake Assembly is clearly one of our most ambitious projects ever undertaken. Each part in this Assembly started as a hand built prototype created on our workbenches. They are cast in bronze and then undergo a final preparation which includes drilling, tapping and brazing together some sub-assemblies. The Steering Arms are a direct replacement for the Pocher stamped metal pieces and attach using the Pocher bolts. The Brake Arm is tapped and attaches with the 2 mm threaded rods. And, the Brake Levers utilize the tapped 0-80 hole in the MML Axle. The 1/16" brass rod (provided in the Kit) fits snuggly in the end of our Clevises (a dab of our Bondini glue is recommended).

The Kit includes the Steering Arms, Brake Arms, Brake Levers, Clevises, 00-90, 0-80, 2 mm Bolts and brass rod.

This Kit does require using the MML Axle (Part No.A002) …the spindles need to be shortened about 1/16" of an inch from the top and bottom, easily done with a file. And, the tie rod provided by Pocher also needs to be fitted. We will fit both at no charge if they are sent to us.

Click here for Instructions

Part No.A037 $100.00 for the Kit

Part No.A037a $140.00 for the Kit, including the Axle (Part No.A002) sized to fit 

MML’s Alfa Leaf Springs

Our thanks to Kenneth Saunders who assembled these.

In our continuing quest to improve the quality of Pochers, Model Motorcars has developed a functional set of Alfa Leaf Springs! Direct replacement for the Pocher springs; requires no modifications. Photo-etched from stainless steel, with the ends preformed with loops (no soldering required), the clamp tubes precut, and all the 0-80, 00-90, 1.0 mm nuts and bolts, and 2.0 mm washers to complete the set. Plus, we include a 1.0 mm wrench! Those 1.0 mm nuts are almost impossible to use without one...

We believe everyone should see just some of the work Brian Yingling did to help make this wonderful addition to our parts catalog. We have been working for almost a year to develop them; many samples, false starts and unexpected problems...

	But...well worth the effort!

Click here for Instructions

Part No A010 $125.00 complete Kit

Click picture to enlarge	Alfa Romeo Item Description	Item Price	Click to buy
	Alfa Headlight Lenses - A047 German tempered glass with pattern, beveled edges.	$30 per pair
	Alfa Safety Wire Kit - A046 The Studs (48) are cast in bronze, nickel plated. Includes 2 yds. of 28 gauge wire and #61 drill. Click here for prototype photos.	$40 complete Kit
	Alfa Safety Wire Studs - A046a The Studs are cast in bronze, nickel plated	$12 Tree of 12
	Alfa Script - A036 Photo etched in .20 stainless steel.	$6 each
	Alfa Crank Cap - A044 Cast in bronze and nickel plated.	$5 each
	Alfa Knock-Off Hubs - A041 Direct replacement of the Pocher provided Hubs. Cast in bronze with a stainless steel threaded rod, nickel plated.	$100 set of four
	Alfa Shock Absorber Assembly - A042 Includes the Chassis Supports, End Plates, Adjuster, End Mounts, 2 mm dome head bolts, 00-90 nuts and bolts and extra shock arms. End Mounts require modification. For the Spider and Coupe - one set of rear shocks. Click here for Instructions	$120 complete Kit
	Alfa Shock Absorber Assembly - A043 Includes the Chassis Supports, End Plates, Adjuster, End Mounts, 2mm dome head bolts, 00-90 nuts and bolts and extra shock arms. End Mounts require modification. For the Monza - two sets of rear shocks. Click here for Instructions	$170 complete Kit
	Alfa Steering and Front Brake Assembly - A037 Direct replacment for the Pocher parts. Requires using the MML Axle (A002) with some modifications. Kit includes 0-80, 00-90, 2 mm Bolts and brass rod. Click here for Instructions	$100 complete Kit
	Alfa Steering and Front Brake Assembly - A037a Direct replacment for the Pocher parts, including a modified Axle. Kit includes 0-80, 00-90, 2 mm Bolts and brass rod. Click here for Instructions	$140 complete Kit
	Alfa Leaf Springs - A010 Direct replacment for the Pocher leaf springs, photo-etched from stainless steel. Complete Kit includes 0-80, 00-90, 2.0 mm washers, 1.0 mm nuts and bolts and a 1.0 mm wrench. The Springs are preformed with a loop. No soldering! Click here for Instructions	$125 complete Kit
	Alfa Tail Light - A040 A wonderful addition to your Alfa. Cast in bronze, includes 0-80 bolts. (does not include the lens.)	$35 each
	Alfa Steering Arm- A035 Direct replacment for the Pocher Steering Arm. Requires drilling and pinning...comes with instructions. Click here for Instructions	$10 each
	Alfa Rear Brake Lever Assembly - A034 Direct replacment for the Pocher provided parts, easy to install. And, now complete with the Wing-nuts! Click here for Instructions	$50 complete set
	Alfa Wing-nuts - A034a Direct replacment for the Pocher provided parts. Cast in bronze and threaded for the 2 mm Pocher rod.	$8 per pair
	Alfa Engine Stands - A031 From the Alfa Engine Kit, cast in bronze, includes a supply of 0.80 bolts, nuts and washers.	$50 per set
	Valve Stems - Z043 A direct replacement to the Pocher provided valve stems, cast in bronze.	$10 set of six
	Alfa Distributor Linkage Kit - A005 14 piece Kit includes everything needed to replicate the prototype linkage. Click here for Instructions	$35 per kit
	Ball Ends - A033 Wonderful addition to our Hardware, cast in bronze and nickel plated. Includes 1 mm nuts.	$7 per pair
	Levers - A032 Another addition to our Hardware, cast in bronze and nickel plated.	$9 per pair
	Alfa Water Manifold - A029 Companion to our Water Pipes, cast in bronze and nickel plated, comes with hose, clamps and flanges Click here for Instructions	$37 per set
	Alfa Engine Kit - A001 Over 500 pieces, resin and bronze casting, photo etched parts and solid oak base.	$700 per kit
	Alfa Engine Kit - A001a This Engine Kit deletes the engine stands, wood base, and data plaque for those who will install it in their Pocher Alfa model.	$625 per kit
	Ignition Wire - Z038 Correct 1930's style ignition wire, proper scale gauge. Click here for Instructions	$5 for 3 feet
	Boots - Z039 Replaces the Pocher rivets! Cast in resin, fits our new iginition wire. Click here for Instructions	$5 for set of ten
	Alfa Chassis Stands - A028 Made from aircraft aluminum with a sanded finish - stands swing free so that the chassis can be turned over. Wide bases give space for tools and parts, and height from the work surface allows space for hands.	$60 per set
	Axle - A002 New axle includes Bronze Bell-Cranks, Bronze Clevises, 0-80 and 00-90 hex-head bolts.	$50 per set
	Clevises - Z028 Bronze casting works with stock 2.0 mm rods and 2mm Pocher screws.	$9.00 for six
	Clevises - Z029 Bronze casting works with stock 2.0 mm rods and 00-90 hex-head bolts (supplied).	$10.00 for six
	Bell-Cranks - Z044 Cast bronze, work with our new clevises with 00-90 fastners	$10.00 per pair
	Aluminum Brake Drums - A026 The drums are exact duplicates of the plastic Pocher drums, machined from aluminum. Wonderfully accurate and neatly made, they can be slipped in placewith no modifications.	$150.00 per set
	Cycle Fenders - A025 Set of resin cycle-fenders for the Alfa Romeo. These fenders feature the correct diameter for the Alfa wheels and a slight "duck-tail" or flare at the rear. Will work in all sorts of applications by attaching the supports to the backing plates of the brakes.	$45 per set of four
	Alfa Romeo Foot Pedals - A023 Nickel plated to match the rest of the Pocher hardware. Set inlcudes accelerator, clutch and brake pedal. Click here for Instructions	$37 per set
	Alfa Romeo Water Pipes & Fittings - A024 Alfa Water Pipe set includes bronze, nickel-plated pipes,"rubber" hose, and photo-etched hose clamps. Click here for Instructions	$32 per set
	Alfa Romeo Hood Latches- A022 Plated in nickel to match the rest of the Pocher hardware, these latches are a direct replacement, require no body work, and use the Pocher screw-eye mount.	$32 per pair
	Resin Replacement Exhaust Manifolds - A019 A replacement for all of those "distressed" exhaust manifolds that came out of the box. Convert a Monza or Muletto to a street engine, or add that finishing touch to a display engine.	$15 per set
	Coffee-Can Coil - A020 An exact scale replica of the Magneti Marelli large diameter ingnition coil seen on Alfa 8c 2300 and Scuderia Ferrari 8C 2600 engines of Thirties. Correct down to the separate resin replica of the ceramic insulator.	$15 each
	Pie-Plate Tachometer- A021 Perfectly sized to take the instrument face on our decal sheet (sold separately) - this large tachometer is just the thing to add a touch of realism to your Alfa interior. Easily mounts right on the steering column.	$10 each
	Alfa Assembled Wipers - R002 Assembled chrome-plated includes rubber blades, bezels and plated nuts.	$40 per pair
	Alfa Gas Cap - A003 Cast bronze replica of correct quick release cap for Monza. Also used for oil. nickel plated	$16 each
	Alfa Racing Windscreens - A004n Cast bronze replica of “Brooklands” folding windscreen — includes lexan and hardware (narrow- a scale 12”)	$20 each
	Alfa Racing Windscreens - A004w Cast bronze replica of “Brooklands” folding windscreen — includes lexan and hardware (Specify wide- a scale 18”)	$20 each
	Alfa Gear Shift Lever & Gate - A006 Chrome plated, cast bronze — correctly tapered gear shift lever and accurate gate.	$35 per set
	Alfa Acorn Nuts - A007 Nickel plated, can be glued or fastened to 1.0 mm rod (not included). Set of 34 is enough to do two Alfa cam covers with two left over	$30 per set of 34
	Alfa Decal Sheet - A008 Includes instruments, , i.d. plates, Modena registration plates, all the engine and firewall plates of the original Pocher stickers.	$20 each
	Alfa Shock Absorber Adjuster Knob - A012 Faithful reproduction of the Siata controller. Mounts on the dashboard and allows the driver to adjust the tension on the friction shock absorbers. Common on Alfas, but also seen on early RR's. Our knob specifically matches the emblem on our Alfa decal sheet. Resin.	$5 each
	Alfa Horn - A013a Cast bronze; drilled and tapped for side or rear mount. Includes brass strap to simulate prototype mount. Polished	$27 each
	Alfa Horn - A013b Cast bronze; drilled and tapped for side or rear mount. Includes brass strap to simulate prototype mount. Matte Finish	$22 each
	Alfa Horn - A013c Cast bronze; drilled and tapped for side or rear mount. Includes brass strap to simulate prototype mount. Chromed	$37 each
	Alfa Breathers - A014 Accurate miniatures of the crankcase breathers used on the prototype 8c 2300 engine.	$48 per set of 4
	Alfa Brake Lever - A015 Has the correct flattened and tapered profile, comes with styrene tubing for handle. Chrome plated	$16 each
	Alfa Radiator Cap - A016 Threaded to fit the Pocher radiator fitting, and includes two sets of printed inserts.	$27 each
	Alfa Fuel Pump Handle - A017 Exact-scale replica of the handle for the fuel pressure pump, nickel-plated.	$16 each
	Alfa Replacement Cam Covers - A018 Cast resin replacement cam covers.	$20 per pair
	Alfa Windshield Wiper Motors - M010 Chrome plated — 2mm threaded mount	$25 per pair
	Alfa Spark Plugs - Z008 Spark Plugs Cast bronze — patterned after early Champion	$18 per set of 8
	Alfa Lighting Kit - M028 For wiring the headlights, taillights and marker lamps. (Includes light bulbs, wire, switch, battery box and instructions) Click here for Instructions	$30 per kit
	1932 Road Map of Italy - Z013 1:8 scale	$10 each
	Real Leather - Z005s Selected from the finest cabretta hides, our leathers are soft, flexible, thin and good smelling., select color from drop down window. Other colors may be available — call or email for custom colors.	$40 per hide
	Piping for Leather - Z005a Select color from drop down window. Most are made from real leather.	$8 per kit

Click here for the complete Model Motorcars Parts List in printable format.

Click here to load the free Adobe Acrobat Reader.

Other items may be available — call to confirm.
Items marked “custom order only” may require an extended lead time.
Domestic shipping and handling is $9.00 for Priority Mail, overseas shipping and handling is $20.00 for Priority Mail International. Prices are in U.S. funds.